Uses and greatest Fit for Under 14kW Generators

Generators that produce lower than 14kW of power feel like lightweights, but a majority of them can supply power in an outage to keep critical circuits operating and offer several conveniences at the same time. Standby generators followed by an automatic transfer switch operate automatically within an outage to keep your home supplied with power, if you are not home. Portable generators won’t operate automatically, but they can complete the task each time a standby generator is just not a choice.

Fuel Consumption

Supplying fuel to a generator within an outage is always a concern. Finding gasoline or diesel fuel during a widespread outage may be difficult or supplies could be restricted. After Hurricane Sandy, some areas rationed gasoline. Smaller generators use less fuel, and consumption is directly impacted by electrical load.

a href=”http://www.generatorpowerforless.com/”>Standby generators use propane or gas and eliminate the necessity for continuous refueling. Some portables can work on propane, and some are able to use propane, propane, or gasoline.

Homes which use LP gas rather than gas must store their fuel in a tank. LP-powered generators from 7kW to 14kW will often be well suited for LP gas installations because they use less fuel than larger generators. Expect a fully loaded 7kW generator to make use of about 1.3 gallons of propane each hour, while 20kW can use up to 2 gallons per hour to create the equal amount of power.

Homes with Lower Power Requirements

Don’t assume all home requires the volume of power a large generator is capable of producing. Many older homes have 100-amp and even 60-amp main service panels, and all the power they could usage is already limited. Even newer homes with 200-amp electrical service don’t utilize that much power.

A 13kW generator can establish 54 amps of current continuously at 240 volts―almost over a 60-amp service, and aside from peak periods, it nears the most power supplied via a 100-amp service in numerous situations. A bigger generator is merely unnecessary.

When air conditioners along with other high-voltage, high-current appliances are used, a transfer switch that manages generator power will assure that power hungry appliances have the power they want.

Mobile Homes

Many mobile homes are designed and developed for 50 to 60-amp service and are supplied via an external disconnect mounted on a pole or post outside the mobile home, combined with the utility company meter. Building codes typically have a 100-amp service as the minimum, and the cabling that runs between your disconnect and also the camper must accommodate very much power. Other jurisdictions allow connection via a 60-amp cord and receptacle.

No matter what, the power needs of mobile homes are normally lower than built-in-place homes, and are good candidates for under 14kW portable or standby generators that operate on LP gas, propane, or gasoline. Gasoline storage is often a problem in camper communities, making LP or gas preferable.

Renewable Energy Systems

Solar and wind power powered off-the-grid energy systems provide their unique power which gets held in batteries. They furnish enough power for power efficient appliances and don’t depend on power through the electric utility. In most cases, these are fully disconnected through the power company.

Generators meant to operate off grid and are powered by LP gas add the space once the sun doesn’t shine or the wind doesn’t blow, and battery levels run low. Typically, these generators produce about 6kW, although larger units can be found. Off grid and sustainable energy systems are designed for minimal power use and environmentally safe operation, making small, power efficient generators the ideal choice.

To find out more go to: www.GeneratorPowerForLess.com

Why Kohler Generators are a fantastic Selection for Home Standby Units

Kohler entered the power generator industry after WW1 after they began building the Kohler Automatic Power & Light Power Plant in 1920 to be used on farms as well as in other isolated locations. During that time, the rural power grid hadn’t been conceived and the power plant filled a niche that filled an easy-growing dependence on electricity. The generator system was revolutionary in that it started automatically whenever power was needed as an alternative to operating regularly.

During World War II, Kohler supplied generators to U.S. troops throughout the world in support of the world war 2 effort. Following the war, they built standby emergency generators for hospitals, businesses and government buildings that needed the best source of standby power―at that period an unheard of concept―Kohler was already there with generator goods that met the demands of the time.

After their entry in the generator market over 90 years back, Kohler Power Systems continues to be manufacturing and supplying standby generators that really work automatically without human intervention.

Kohler Home Standby Generators

Kohler’s home standby generators supply power once the electric utility fails. Joined with an automatic transfer switch, the units standby around the clock to start and run automatically in the event of the power outage.

Once the power fails, the generator waits a short time to ensure the outage just isn’t momentary. Then an engine starts and reaches operating speed. The automated transfer switch disconnects through the utility supply and connects to the generator. Electricity is restored to selected circuits through the entire home (based on the transfer switch configuration). Once the utility line is re-energized, the transfer switch restores utility capacity to the home. The generator runs for a minute to chill down, then shuts off.

Kohler supplies home standby generators in sizes that cover anything from 8500 watts to 100kW that satisfy the power needs of even most luxurious homes and a lot of businesses.

Automatic Transfer Switches

Standby generators require an automated transfer switch to work automatically. Kohler designs their automatic transfer switches specifically to utilize their standby generators. They’ve many different designs to meet the requirements of most homes.

The Intelligent Transfer Switch Load Center combines a principal service panel having an automatic transfer switch which includes an intelligent load-shedding power management system. The indoor model has room for 40 circuit breakers, the outdoor NEMA 3R model has room for 28. This model can replace the main service panel.

Other transfer switches manufactured by Kohler include 100 to 400 amp models with or without load centers and power management capabilities. Models without load centers can manage utility and generator power for your home or maybe a subpanel, while load center models are designed to operate like a subpanel with the main circuit breaker panel as the source.

Kohler Power Systems Reliability

Kohler has a long history of reliable power solutions. Their innovative systems have been providing power both at home and throughout the world since the 1920s, and they also were one of the primary to provide automatic standby generators. Their residence standby generators come with an industry-leading warranty that covers their units for five years or 2000 hours. The generators can operate for days or even weeks if needed, and so their models are factory tuned to perform on either LP gas or Gas, driving them to efficient and reliable performers that offer utility quality power when needed.

For more information, please go to: www.Got-Generators.com

Understanding the term Home Standby Generators

Residential use generators supply power to homes once the electric utility supply is lost. Utility power interruptions occur due to weather related events including high winds, ice buildup on wires, wild animal damage, motor vehicle collisions, and damage caused by many other acts of nature or man. Devices and systems that depend upon electrical power cannot function throughout an outage unless a supply of emergency power is available.

Permanent Installation

Standby generators are invariably able to operate, 24 hours a day, seven days weekly. They may be permanently wired to the home’s electrical system using an automatic transfer switch, and attached to the home’s natural or LP gas supply pipes. A Natural or LP gas hookup ensures the generator has always a sufficient supply of fuel available and does not require frequent refueling throughout an extended outage.

Automatic Transfer Switch

Automatic Transfer Switches work alongside the standby generator’s controller. After the generator starts and is able to accept the electrical load, the automated transfer switch disconnects the electrical system from the utility supply and connects it to the home standby generator. The change in power from one supply source to another is automatic and controlled by electronic switches inside the transfer switch. If the electric utility restores power, the transfer switch reconnects the utility supply and disconnects the generator.

Automatic transfer switches usually are made by the generator’s manufacturer to meet the requirements of a particular standby unit, since they work directly together with the standby generator’s controller. They also provide different alternatives, including power management, with respect to the needs of the consumer.

Some transfer switches install between your utility meter as well as the main service panel to supply power to the whole panel. Others install as a subpanel from the main service panel and just supply selected critical circuits, including pumps, refrigerators, furnaces, and medical equipment.

Operation

Standby generators are automatic, permanently installed equipment that do not require frequent refueling with liquid fuels. They operate without operator intervention, except for regular, scheduled maintenance. Unlike portable models which should be connected and started when power is needed, the standby home generator operates in a fully automatic mode, whether or not the homeowner just isn’t present.

Standby power means the generator is able to operate always. When an outage occurs, the generator starts following a short delay, then this transfer switch moves your home onto emergency backup power. It happens quickly and without intervention, but it is possible to find a short time when the home is without electrical power. Some electronics may require an uninterrupted supply that operates off battery power before standby generator will be able to start and connect to the home’s electrical system.

Installation

Installation requires building permits and the services of a qualified electrician to set up the transfer switch and make the mandatory electrical connections, and also a plumber in order to connect the generator for the home’s gas supply. Inspections from the prepared gravel bed or concrete slab usually are required before installation, as well as the finished work after installation. Adherence to National Electrical Codes, Plumbing Codes, National Fire Protection Association Codes, and native ordinances is essential.

The location chosen for installation must be sure that exhaust gases will not likely enter in the home and using CO detectors is additionally required.

Home standby generators complete when electric utility power becomes unavailable to guarantee the safety of homes, property, and families.

To find out more, go to: www.BackupHomePower.com

Entire House Generators – a review of what it really means, and how much power you receive

Some standby generator packages are identified as providing “entire home power” meaning they’re able to power everything at your residence. The packages more often than not have an automatic transfer switch with power management features.

Alone, “entire home power” ensures that the whole property is furnished with power, however not all generators are capable of producing enough power to support all appliances and lights simultaneously.

Home Power Use

The typical new home in the USA carries a 200-amp service panel with a lot of circuit breakers. In the event the amperage of all breakers within the panel are added up, they may total around 800 amperes, far more over exactly what the panel or main breaker are prepared for. If all of the home’s appliances and lights were switched on, the complete would still not exceed 200 amperes and the main breaker wouldn’t trip.

Safety and convenience dictate the size of the primary service panel and the volume of circuits it supplies. The size of the primary breaker is not a good indicator of the volume of power the entire house uses.

Power Management

Managing power takes two forms. Homeowners do their part by switching off nonessential appliances and lights while operating on standby power. What produces a nonessential appliance is determined by your situation along with the capability of the entire house generator. Power management devices for example load-shedding controllers or digital power management systems prevent backup generator overloads by limiting the volume of high-demand appliances that operate simultaneously.

Automatic Transfer Switches

The automated transfer switch is an essential part in the entire home generator system. Their installation configures them since the gatekeeper for electricity for the entire home. During normal operation, they send power from the electric utility to the main service panel. When utility power fails, they disconnect the utility lines from the home and route power from the entire home generator to the main panel.

To satisfy electrical codes, the automatic transfer switch current rating within a entire home power configuration must equal or exceed the primary circuit breaker current rating. A 200-amp main circuit breaker needs a 200-amp or greater automatic transfer switch. By using a smaller switch for entire home power may cause a fire or permanently damage the switch.

Entire House Generators

Generators are rated in watts (W) or kilowatts (kW), a measure of the work electricity is capable of doing. Air-cooled generators for entire home power begin with ratings of around 8,000 watts (8 kW) and top out at approximately 20,000 watts (20 kW). Liquid-cooled generators for residential applications offer 20 kilowatts to 65 kilowatts of electricity.

By comparison, 100 amp main circuit breaker are prepared for about 24,000 watts of power along with a 200 amp panel about 48,000 watts of power. Take into account that your home never uses the volume of power the primary breaker is designed for.

Picking a Home Standby Generator

For most applications, you shouldn’t have or economical to install a whole house generator able to offering the equivalent power the primary circuit breaker is designed for. By utilizing power management devices and judicious homeowner power use, smaller generators will supply the entire house with electricity.

Perform a power audit to determine all the power used at the time. Figure out what high voltage appliances are necessary and which are not. Finally, decide on a backup generator package which will match the power needs of the entire home and employ power management devices to regulate the energy supplied to high profile appliances for efficient entire home energy that suits you.

For more info go to: www.BackupHomePower.com

14kw Standby Generator Comparison

When the utility power fades, standby generators supply backup emergency power during the entire power outage. Whether a major hurricane or even a fast-moving local thunderstorm, power outages may last a few hours, weekly, or so long as per month or maybe more. With a way to obtain standby power from the home generator, residents usually stay within their homes as opposed to seeking shelter elsewhere.

Home standby generators operate automatically and so are permanently linked to the home’s electrical system by using an automatic transfer switch which is usually given by the generator’s manufacturer. The switch and generator controller come together. When the power fades, the generator starts and the transfer switch connects the house to the generator and disconnects it through the utility company. After utility power is restored, the connections are reversed and the generator shuts down.

Standard Features

Most 14kW standby generator manufacturers offer similar features and own make of extra functionality. The engines have a very fully pressurized lubrication system similar to that in cars and may de-activate for low oil pressure or high engine temperature. They all run the generator by taking exercise cycles to keep the generator lubricated preventing seals from drying out. After operating under load, they run for any short, no-load cool-down period.

Utility power is mostly clean as well as free of excessive noise. The AC frequency is steady and unvarying, and also the voltage stays inside a certain range, rarely falling below 108 volts and never exceeding 125 volts. Standby 14kW generators meet and often exceed exactly the same requirements and still provide utility-quality power, even though the loads change frequently or while starting large, heavy-duty motors.

Continuous Power

Standby generators are rated by the volume of continuous power they are able to supply, and not all supply the rated continuous power on all fuels. Kohler Power Systems and Generac Power Systems are a couple of manufactures of 14-kilowatt standby generators that run on LP or natural gas.

Some manufacturers derate their multi-fuel generators when operating on natural gas because natural gas contains about 10 percent less energy than propane. An electric that will be powered by propane will likely run okay on gas main with a few adjustments, but because the gas has less energy, the engine cannot create exactly the same power.

Remote Operation

Generac offers Mobil Link as one optional accessory. It uses cellular txt messaging system to communicate with an internet-based dashboard that owners have access to everywhere with a net connection, bringing the Generac14kW standby generator controller to tcomputers around the globe. Status text messages are given to cellular phone accounts. An electronic digital cellular phone connection with texting is necessary in the 14kW generator installation site.

Kohler’s On Cue Remote Management Systems allows owners to control their 14kW standby generator from around the globe. Status messages can be delivered to dealers, owners, or both in order that maintenance is completed as required and problems dealt with before they result in a generator to fail. Users can see real-time status, see and clean fault codes, manage generator performance, and review generator history. It provides for operation of multiple generators from just one account. The On-Cue Management Software requires Windows XP, Vista, Windows 7 or Windows 8 and generator web connection.

Warranty

Kohler covers their 14kW standby generators using a consumer warranty of five years or 2000 hours for standby operation when reliable on-grid utility power can be acquired, and includes labor throughout the first 2 years after installation. For off-grid applications where utility power isn’t reliable or available, the warranty covers parts for 18 months or 1000 hours.

Generac’s 14Kw standby generator carries a 5 year, 2000 hour limited consumer warranty for on-grid applications. Off-grid applications are not covered and may void the warranty. Comprehensive parts, labor, and mileage are covered for the first 2 years, parts throughout the third year, and limited coverage in the engine block and alternator throughout the fourth and fifth years.

For more info go to: www.NPSGenerac.com

Cummins Onan Cold Weather Package

Cummins Onan standby generators come in a number of packages including various automatic transfer switches and cold weather packages. Standby generators from Cummins Onan operate automatically once the utility power is interrupted plus they are linked to a computerized transfer switch.

Cold temperature packages allow the generator engine to get started up with less effort during cold weather, providing more reliable operation under harsh, winter weather conditions.

Cummins Onan Standby Generators

Cummins is really a trusted name in power generation, and standby generators are not any exception. Home standby units for emergency power are the 20-kilowatt and 13-kilowatt air-cooled models, and the 20 kilowatt liquid-cooled machines.

Cummins Power Generation combines their residential standby generators with some other automatic transfer switches to provide the needs of most home standby customers with utility-quality energy that meets the needs of even most sensitive of electronics. The generators have a 5-year, 2000 hour limited consumer warranty.

Winter Equipment

Cummins recommends incorporating cold-weather accessories to use in climates where temperatures drop to zero degrees Fahrenheit or lower.

A breather heater warms the engine breather tube to stop ice build up during cold temperatures. It connects to a cold weather kit (available separately) or into any winter equipped generator. The breather heater is suggested to use in environments where temperatures drop below zero.

The battery blanket warmer is a flexible heater that wraps around the battery it warm when temperatures drop below -10 degrees. A separate 120-volt outlet is necessary to turn on the heater.

Cold temperature kits provide an engine oil heater as well as an alternator dryer. The engine oil heater allows easier starting by keeping the oil warm and fluid, and permits the lubrication system to produce oil faster after the engine starts. Alternator dryers keep frost from accumulating on the alternator.

20-Kilowatt Cold-Weather Packages

Four 20-kilowatt cold temperatures packages combine cold-weather equipped generators with automatic transfer switches. The 20kW standby generator packages may start and run a 5-ton ac and still have fully automatic power management capability.

The automatic transfer switches can be 100-amp or 200-amp, service-entrance-rated automatic transfer switches including whole-house-power management capability and 2-amp battery chargers, all inside a NEMA 3R enclosure rated for outdoor installation. Included as well are an inside wireless monitor and internet monitoring with email notifications.

The RS20-C150 comes with the 100-amp ATS, as the RS20-C250 contains the 200 amp model. These generator packages are US EPA and CARB certified for emissions.

For quick and easy installation, Cummins Onan includes two, 100-foot installation harnesses with all RS20-C1100 and RS20-2100. The C1100 includes the 100-amp transfer switch the C2100 with the 200-amp ATS. US EPA emissions only. Not accessible in California.

13-Kilowatt Cold-Weather Packages

The 13-kilowatt standby generator packages from Cummins Onan include five different kinds. All include indoor wireless monitors and remote internet monitoring with email updates and they are 49 state compliant for US EPA emission standards.

Model 13GSBA-6711A is really a standby generator only equipped for winter operation.

Packages including the automatic transfer switches would be the RS13-150, RS13-250, RS13-C1100, and RS13-C2100. The transfer switches are service entrance, NEMA 3R rated for outdoor installation and designed with the two-amp 12v charger and whole-house-power management.

The RS13-C150 has a 100-amp switch and includes two, 50-foot wiring harnesses. The RS13-250 includes the 200-amp switch and also the two 50-foot wiring harnesses.

The RS13-C1100 together with the 100-amp switch along with the RS 13-C2100 with 200-amp switch each include two, 100-foot wiring harnesses.

For more info go to: www.Got-Generators.com

Generac Generators Updates the 20kw Standby Generator to New Model – 6244

Generac Power Systems introduced the updated model 6244, 20kW Guardian Standby Generator using the new Evolution Controller. The most popular package previously sold under model #5875 which includes the 200 Amp, Service-Entrance-Rated Smart Switch, a mechanical transfer switch. The new form of the Guardian Series backup generators has been around since January on the 2013 International Builder’s Show in Vegas, Nevada.

Generac’s Guardian Series Home Standby Generators work with an automatic transfer switch to supply power to your house within a power outage without homeowner intervention and work on either propane (LP gas) or Gas, eliminating the necessity for frequent refueling.

Evolution Controller

The Evolution replaces the Nexus Controller and includes numerous updated features. The new interface is really a back-lit membrane keypad to exhibit generator status instantly. Other extra features exceed the cosmetic. The live view screen still shows two lines of text and reports maintenance logs, generator status alerts, and alarms, but new functional features help house owners with better information regarding battery health, as well as alarms for your wall charger, overload, and fuse warnings to recognize issues before they become problems.

The new Evolution also supplies a computer usb port that permits a tech to update the firmware without taking out the controller―a far better solution than swapping out your old Nexus controller for just one with updated programming.

Engine Upgrades

The Guardian group of generators uses Generac’s specifically created overhead valve industrial engine―the only engine in the industry which was created specifically to be used in standby generators. Generac has produced the engines in their standby units better to service and it has improved starting at a variety of temperatures using the new updated model line. A redesigned fuel system eliminates the choke and boasts a standard throttle body.

Guardian generators ship from the factory willing to run on natural gas. Conversion to LP gas happens to be simple and took only a few minutes, nevertheless the new design allows conversion without tools and just has a couple of seconds. It is actually turning a knob.

Entire Home Power

With 20,000 watts of power, the 6244 can run many kitchen appliances including air conditioners. The Smart Switch boasts a load-shedding controller that permits high-voltage appliances to perform without overloading the generator. The Smart Switch senses an overload condition and turns off high-voltage loads in order of assigned priority.

Without any additional hardware, the Smart Switch can control two air conditioners. The addition of an electric Management Module core kit allows adding another high-voltage device. Fully loaded with four Power Management Modules (PMMs) enables the smart change to manage when using two air conditioners and four additional high-voltage, high-current appliances.

Neighborhood Friendly Design

The 20kW 6244 will fit easily into any suburban neighborhood. The all-metal enclosure is powder coat painted for an attractive appearance making it from Galvaaneal steel for a long, corrosion free-life. At only 66db, it’s quieter than many central air conditioning unit units―important for keeping the neighbors happy when their capability has gone out along with their windows are open up. Placement is made easy by compliance with National Fire Protection Association codes and regulations for placement at 18 inches from the home.

Generac leads the industry with standby generators for backup home power, and today the Guardian lineup receives a necessary update.

For more info go to: www.NPSGenerac.com